OK, not the best title to describe what I’m doing, but this crank knitting lark is getting me excited (yes I know, I need to get out more)!
Well, I’ve had my Addi Express knitting machines for about 6 months now and I’ve discovered a wealth of possibilities for a variety of knitted projects. This means that you don’t have to stick with making hats and scarves all the time! With a combination of hand-knitting and machine cranking, you can create a LOT of different projects.
See below for my simple pattern for an Infinity Scarf or Cowl.
I’ve put together a set of essential tools that I use specifically for crank knitting. Tools such as:
- 6mm circular needles – two of these
- 5mm, 5.5mm and 4mm crochet hooks
- Loom hook (or use a dental hook) – ideal for retrieving a dropped stitch from the machine.
- Measuring tape
- Yarn needle
- Stitch holders
- Scrap yarn – about 25g or more of smooth yarn to use for the casting on and/or off. Can be re-used for many projects. Note: It is not essential to use this method as the stitches are large enough to pick up and knit directly from. But having said that, it cuts out the guessing game when it comes to identifying a live (workable) stitch.
- Handheld counter – in case your Addi digital counter has gone bananas, like mine has!
What I have found is that not every yarn in my possession will work with the Addi. This is a big problem for yarn stash that I would SO love to use for a cranked project. For example, I have a pure linen aran weight yarn that I bought in France. Beautiful stuff, but would the bugger play ball and work for me? No! It kept getting caught on the needles, nearly breaking them off. The same thing also happened with a cotton ribbon yarn that I have.
So, given my experience, the yarn types I’ve had to avoid so far are:
- Linen (of any kind) – it appears that its lack of elasticity makes it impossible to loop around the needles properly.
- Cotton in Worsted weight or heavier – for the same reason as Linen.
- Flat (ribbon) yarns – it just gets caught! It’s infuriating!
- Super Chunky (Super Bulky) yarns – hard to crank. Too fat, I guess.
PATTERN: Crank-it! Infinity Scarf/Cowl – a bit more interesting than a regular scarf.
Made with the Addi Professional (22-pin) only. It is made out of 3 tubes of knitting which are later sewn together side by side. The ends are seamed by knitting the live sts together (or grafting).
For the Infinity Scarf: 180g total of any wool-based DK or Worsted weight yarn (approx. 2 skeins).
Sample shown uses Alpaca Supreme by John Arbon (alpaca/merino/silk) fingering weight, held double with Royd Moor Cashmere 4ply (100% cashmere).
For the Cowl: 115g total of any wool-based DK or Worsted weight yarn (approx. 1-2 skeins).
Sample shown uses Galenas Merino by Three Irish Girls (100% merino) worsted weight.
How to Make
(Don’t forget to check the Handy Tools list in article above)
For the first tube, with scrap yarn, cast on and work 4 rounds on the Addi 22-pin. Break off scrap yarn.
Change to your chosen yarn and crank a tube about 120cm (47″) long*. Cut off yarn.
*Depending on yarn weight, this can be anything between 150-190 rounds for the Infinity Scarf and about 85-100 rounds for the Cowl. Keep a row count record of the first tube, then duplicate this count for the other tubes.
Change to scrap yarn and cast off for about 4 rounds. Remove work from machine.
Repeat for the other 2 tubes. Once all 3 tubes are done, pull the tubes at various angles to kick the stitches into line then lay them flat, allowing a little time (say 20 minutes) for the stitches to relax back into position (press if necessary). Later on, using mattress stitch, sew the sides together along the vertical column of stitches (not including the cast on/off sts).
Undo the cast on scrap yarn stitches on all 3 tubes – you should be left with a total of 33 (3 x 11) live sts on front side (whichever side is facing you) and the same number of sts on the back of the piece.
[Transfer the 3 sets of Front sts onto a 6mm needle*, then repeat the same for the Back sts. Make sure both needles are pointing to the right ready for knitting. Similar to working a 3-needle-bind-off, using a spare needle (or the other end of a circular needle) KNIT together the front sts with the back sts. From here you will have 33 single row of sts.]
*This needle size closely matches the Addi tension, for me anyway!
Put these sts on hold for later. For the other end of the piece, undo the cast off scrap yarn, then repeat [ ] once more. Leave sts on needle.
There are 2 ways you can combine both ends of live sts:
1) 3-needle bind off: With WS (wrong side) facing and right sides together, knit the 2 rows of sts together and bind off at the same time. Result: This will leave a visible seam line. The seam edges will be set inside the scarf/cowl and not visible on the outside.
2) Grafting (Kitchener Stitch): Thread a needle with yarn about 3 times the width of the piece. With RS (right side) facing and wrong sides together, graft the front set of sts together with the back set. Result: This will leave a seamless fabric.
Weave in ends, block if necessary…. and tadaa! Wear with pride!
Please share your projects pictures or tips. I’d love to see them! 🙂